挤压铸造ZA27合金阻尼性能研究

对比研究了ＺＡ２７合金挤压铸造和重力铸造时的阻尼性能，结果表明：挤压铸造试样内耗高于重力铸造，是重力铸造的１．２倍；挤压铸造试样传递函数低于重力铸造；在频率高于２５　Ｈｚ时，ＺＡ２７合金的阻尼作用效果明显，且挤压铸造成型的机件振动衰减效果比重力铸造强．     

制备工艺对弧焊成形件性能影响研究进展

阐述了弧焊工艺参数、搭接量、层间冷却时间、焊接路径规划以及激光-弧焊复合焊接工艺对成形件组织性能(残余应力、温度场、组织、硬度、抗拉强度)影响的研究现状,总结了尺寸与性能控制一体化快速制造、尺寸控制和表面改性复合快速制造、基于机械加工特征的性能控制等研究新进展,最后指出未来性能控制研究应在性能控制建模、几何尺寸与表面性能控制的顶层设计、弧焊快速制造与纳米表面工程的复合运用等方面加以重视。     

对装备需求的辨证认识

分析了装备发展的根本原因和装备需求的本质，提出装备需求同时具有客观性和主观性2种性质。阐述r客观与主观装备需求的主要特点和相互关系，以及认清装备需求的本质对装备需求开发乃至装备发展工作的现实意义。提出发挥人的主观能动性，创新装备需求，是实现装备科学发展和扭转装备发展被动局面的最佳途径。     

超细矿物微粉改善2号坦克润滑脂摩擦学性能研究

采用球盘式摩擦磨损试验机，研究了羟基硅酸盐超细矿物微粉作为2号坦克润滑脂添加剂对钢／钢摩擦副的润滑性能，利用扫描电子显微镜（Scanning Electron Microscopy，SEM）和X射线能谱仪（Energy Dispersive Spectrometry，EDS）分析了磨痕表面形貌及典型元素的面分布情况。结果表明：超细矿物微粉可显著改善2号坦克润滑脂的抗磨减摩性能，含2wt％矿物微粉的润滑脂同单一2号润滑脂相比，摩擦系数降低了约44％，钢盘磨损率降低了约70％，这与羟基硅酸盐可在摩擦表面形成一层富含O，Si，Mg，Al等元素的摩擦表面膜密切相关。     

复合材料修补金属裂损结构吸湿老化的试验与有限元分析

暴露在湿热环境中的复合材料修补金属裂损结构易吸湿老化,导致该结构性能下降,服役寿命缩短。为研究吸湿性对复合材料修补金属裂损结构修补效果和耐久性的影响,利用试验方法分析了吸湿性对复合材料胶补金属裂损结构及胶黏剂力学性能的影响;利用有限元方法评估了吸湿性对复合材料胶补金属裂损结构试验件修补效果和耐久性的影响。研究结果表明:吸湿后含穿透双边裂纹铝合金板玻璃纤维单面胶补试验件的疲劳裂纹扩展寿命和极限载荷的平均值分别下降为吸湿前的71%和90%;吸湿造成拉伸条件下复合材料胶补金属裂损结构胶层失效模式由内聚破坏为主转变为界面破坏为主;在"湿-热"老化30天后,E44/聚酰胺环氧树脂胶黏剂试验件吸水饱和,弹性模量下降为未老化前的40%,塑性应变超过了总应变的25%;有限元分析发现胶层损伤受吸湿影响明显,吸湿性加速了胶层损伤,且裂纹长度越长,加速作用越明显;同时吸湿使得裂纹尖端的J积分值急剧增大,导致修补结构的疲劳裂纹扩展寿命缩短,裂纹长度越长,吸湿性对于复合材料胶接修补效果的危害越严重。     

军队科研机构推进国防知识产权转化运用

军队科研机构作为国家科技创新体系的重要组成部分,承担了大量科技创新任务,产生了许多具有自主知识产权的高水平科技成果,推动军队科研机构国防知识产权转化运用,是贯彻军民融合发展战略的必要途径。分析了军队科研机构国防知识产权转化的现状及制约转化的现实障碍,并结合实际探讨了推进军队科研机构国防知识产权转化的建议举措。     

Effect of tool rotational speed on the particle distribution in friction stir welding of AA6092/17.5 SiCp-T6 composite plates and its consequences on the mechanical property of the joint

This study investigates the effect of tool rotational speed (TRS) on particle distribution in nugget zone (NZ) through quantitative approach and its consequences on the mechanical property of friction stir welded joints of AA6092/17.5 SiC_p-T6 composite. 6 mm thick plates are welded at a constant tool tilt angle of 2° and tool traverse speed of 1 mm/s by varying the TRS at 1000 rpm, 1500 rpm and 2000 rpm with a taper pin profiled tool. Microstructure analysis shows large quantity of uniformly shaped smaller size SiC particle with lower average particle area which are homogeneously distributed in the NZ. The fragmentation of bigger size particles has been observed because of abrading action of the hard tool and resulting shearing effect and severe stress generation due to the rotation of tool. The particles occupy maximum area in the matrix compared to that of the base material (BM) due to the redistribution of broken particles as an effect of TRS. The migration of particles towards the TMAZ-NZ transition zone has been also encountered at higher TRS (2000 rpm). The microhardness analysis depicts variation in average hardness from top to bottom of the NZ, minimum for 1500 rpm and maximum for 2000 rpm. The impact strength at 1000 rpm and 1500 rpm remains close to that of BM (21.6 J) while 2000 rpm shows the accountable reduction. The maximum joint efficiency has been achieved at 1500 rpm (84%) and minimum at 1000 rpm (68%) under tensile loading. Fractographic analysis shows mixed mode of failure for BM, 1000 rpm and 1500 rpm, whereas 2000 rpm shows the brittle mode of failure.     

国防知识产权运营市场化研究

提高国防知识产权转化应用水平,关键是解决制约国防知识产权转化应用的体制机制问题。可借鉴普通知识产权运营经验,以市场化方式促进国防知识产权运营工作。针对当前运营中出现的市场失灵现象,从创新政府治理模式、引入市场机制、增强法律法规建设、搭建公共服务平台等途径入手,逐步理顺政府与市场的关系,进行国防知识产权运营市场化改革。     

Modeling and realization of real time electronic countermeasure simulation system based on SystemVue

In this paper, we proposed a new design scheme of real time electronic countermeasure simulation system. This paper mainly expounds the modeling and realization methods of each part of the whole simulation system, and the real-time property of system has been lucubrated. Electronic countermeasure simulation system is the key part of military training of individuals; it can also allow the realistic evaluation of the performance of modern equipments and techniques. As a proof, we have drawn up a series of simulation scenarios, such as radar electronic reconnaissance simulation scenario, to explain the feasibility and the superiority of our modeling scheme in this paper.     

铝合金-纯铝-钢复合板爆炸焊接试验及性能研究

通过设计爆炸焊接试验复合了铝合金-纯铝-钢爆炸复合板,对其界面形态、显微硬度及力学性能进行了研究。结果表明,铝合金-纯铝界面纯规则正弦波形,纯铝-钢复合板界面波形较小,铝合金-纯铝-钢复合板的界面剪切强度在75 MPa以上,爆炸复合过程中,纯铝与钢界面生成了金属间化合物,其界面处基体金属发生强烈的塑性变形。复合板变形及组织变化的结果造成复合板界面处的显微硬度最高,随着距界面距离的增加,两侧基体金属的硬度逐渐降低。